Visslo F8 premier Servisní příručka

OPERATION MANUAL 3D PATTERNLESS LENS EDGER/ F8 premierRev. 1014-0912

2.2 Control PanelFig. 41. : Lens material --- Choose PLA(Plastic), HPL(High index plastic),

4. : Use when choose rimless polishing mode. {(This key is not working in Type GLS(Glass)}5. : Use when

13. Indicate changed volume of the figures to enter Use key and shows by 0.01, 0.1, 0.5(mm)14. Indicate process stepsLayout Mode

: Nylon : two-point (drilled)19. Edging mode : Auto mode : Controlled mode : EX lens mode*

23. Optical centerFig. 6fig.6Fig. 7 : Distance between rim center and optical center by the steps of 0.1mm : Crossing distance

25. PD (Pupillary distance) (30.00mm~99.50mm by the steps of 0.5mm)26. SIZE (Size compensation value) Indicates the compensation value for the com

2.3 Edger key Switch 2.3.1 Menu : Retouch -- minor adjusting : Safety Bevel -- chamferring mode on/off

2.4 Edging unit Fig.9 Edging unit*Roughing wheel for glass lens*Roughing wheel for plastic lens:Roughing wheel for plastic,poly carbonate, acryl

3.1. Choose edging conditions1) Choose lens materials : Plastic : High index plastic : Polycarbonate :

Automatic bevelingControlled groovingAutomatic groovingRilmelss(flat) edgingEX Lens edgingEdging modeControlled beveling

WWW.VISSLO.COM#301, Apollo Town, 18-36, Sanbon-Dong, Gunpo-City, Korea Tel+82 31 349 8693 Fax+82 31 349

3. 2. The input of grinding conditions3.2.1.Standard lens : The vertical distance between optical center and frame center : T

3.2.2.Bi-focal lens ':The distance between staright line point downside of lens shapeand center point of distinguished line upside

4.1 Standard edging(Beveling) 4.1.1 Automatic edging1) Choose edging conditions : otherwise :2) Fix the lens to ad

3) Push and start edgingMeasure lens thicknessRough edging(Switched to the screen of beveling shape)Delicate edgingWhen choose

4.1.2 Data Controlled Edging1) Choose edging conditions : otherwise :2) Fix lens to adaptorRef.) Article 2 of 5.1.1.

4) Simulate beveled section : Position line of section viewing is rotated clockwise. : Position line of section viewing is rotated uncloc

6) Push again and start edging.Rough edgingDelicate edgingPolishing (When choose )Chamfering (When choose

4.2 Optional edging 4.2.1 Edging by the frames4.2.1.1 Rimless standard1) Choose edging conditions :* No need selecting AUTO mode and CONTR

when lens is fallen to wheel if take the chuck off on condition that wheel is not stopped throughly.* Additional groovingGrooving may be able to be s

4.2.1.2 Grooving (A) Automatic edging1) Choose edging conditions : :* Glass edging is not available in grooving.2) Fix lens to adaptorRef.

1. Introduction 1.1 Product outline & Intended use 1.2 Lens materials and edging modes 1.3 Accessary and locking / unlocking procedure2.

is not stopped throughly.WarningBe sure to close sliding cover certainly before start edging.Edging may not be able to be worked as sliding cover is

(B) Controlled Edging1) Choose edging conditions : :2) Fix lens to adaptorRef.) Article 2 of 5.1.1. Automatic edging3) Push

lens edge and to the thickest place of lens edge in turns by pushing5) Regulate beveling positionBeveling position may be able to be regulated in RAT

when lens is fallen to wheel if take the chuck off on condition that wheel is not stopped throughly. 4.2.2 Classifications by lens4.2.2.1 EX le

lens edge and to the thickest place of lens edge in turns by pushing.It is not available to get good shape of lens by standardbevel edging because of

again.Position section viewing line at the thinnest place of lens. 4.2.3 Edging by the functions4.2.3.1 Frame change edgingThis job is worked f

4.2.3.2 Safety mode edgingFast mode is to be switched to safety mode if press key for 3 seconds.Safety modey may be able to edge mor

5.1 Data store and use 5.1.1 Store dataPush and transmit traced data to screen.Position cursor at ,

1) Change Parameter * Initial Value of FPD : Means FPD value, early assigned* Initial Value of PD : Means PD value, early assigned* Height of Optical

* Rework : Remove chamfering : Choosing chamfer or not in case rework2) Regulate Size : Necessary compensation value for regulating lens size* Finish

5. Save and retrieve data 5.1 Save and retrieve data 5.1.1 Save data 5.1.2 Retrieve data 5.1.3 Adjust the parameters6. Install

* Rotation Limit : Edge as much as rotations if edging is not done4) Regulate Bevel : Necessary compensation values for regulating beveling--> Beve

* Chamfer Width <BVL, F>, <BVL, R> : Compensate width* Chamfer Width <FLT, F>, <FLT, R> :Compensate width6) Regulate Axis : Ne

How to check①" Movement Inspection" select ② "Head Contact Sensor Status --> 0 ON" are turned up and head is going down.Co

Chapter 6. Installation and check, maintenance,cleaning 6.1 Installation1) Temperatures to install : 5~40 , to store:-25~80 Humidity

6.2 Check1) Be sure to check the equipment is off certainly before working and after.2) It is necessary to check the equipment over all every two y

6.3 MaintenceCaution1) Unplug if the machine is not working for a long period.2) Cover tracing unit and edging unit unless the machine is not worki

6.4 Cleaning1) Clean pins of power plug with dried fabrics from time to time.2) Keep local wastes handling regualtions when dispose wastes.3) Clean

Warning : Means the risk which may cause dead or serious wound if the operator doesn't care. Caution : Means the risk which may ca

3) Be careful to decide lens materials. Wrong choice may break the lens and leesen the use expectancy of the wheels.4) Be sure to chamfer both side

7.3 WiringCaution1) Do not take code wire but plaug itself when take the plug off from power inlet. Impared code may be able to occur electric le

1.1 Outline of the Product & Intended use The lens Edger ( Model:F8 premier ) is edging the optical lens according to the tracing data whi

This system provide self-analysis functions by watching and checking always. Abnormal condition is detected,systme is stopped automatically and follo

-Indoor use only -Altitude up to 2000 m -Operating temperature up to 40 °C -Maximum relative humidity up to 80°C

Chapter 10. Symbol Description

1.3 Accessaries &locking & unlocking procedure 1.3.1 Composition 1) Main body 1 Unit 2) Manual blocker 1 Unit ( Optional ) 3)

1.3.2 Accessaries and Locking & unlocking procedure Warning Be sure to take fixing unit out before turning on certainly since fixing uni

*chock any interference with movement*chock any interference with movement*chock any interference with movement*chock any interference with movementLo

* Control Panel : Shows and control all menu* Edger Key switch : Controls conditions before edging* Sliding Cover : Shields the noise and filthy wat